All articles
EV Charging November 16, 2026By LTBL Energy

EV Charger Load Calculation: Can Your San Diego Home's Panel Handle It?

You bought an EV, picked out a Tesla Wall Connector or another Level 2 charger, and now there's one question left: does your electrical panel have room for it?

You don't answer that by looking at how many empty breaker slots you have. You answer it with a load calculation, a code-based check of how much power your home already uses compared with what your panel and service can safely deliver. Here's how it works for San Diego homeowners, and why it often decides whether you need a panel upgrade or can go straight to installing your charger.

What a Load Calculation Actually Measures

Every home has an electrical service (the capacity coming from SDG&E, often 100, 125, or 200 amps on the main breaker) and a panel that splits that power into circuits. A Level 2 EV charger is one of the largest loads most homes ever add, and it runs for hours at a time.

A load calculation answers one question: after we add the charger, does the home's total expected demand still fit within the service rating? If it does, the charger can usually go on the existing panel. If it doesn't, you have options. We cover them below.

Why EV Chargers Get Special Treatment

Electrical code treats EV charging as a continuous load, so the circuit is sized at 125% of the charger's output. That's why a charger set to 48 amps goes on a 60-amp circuit, and one set to 32 amps goes on a 40-amp circuit. The bigger the charger setting, the more of your panel's capacity it uses.

The Two Ways Electricians Calculate Existing Load

California is on the 2025 California Electrical Code, which took effect January 1, 2026 and is based on the 2023 National Electrical Code. For an existing home, it gives an electrician two main ways to figure out how much capacity you're already using.

Method 1: The Calculated Method (NEC 220.83)

This method builds your home's load from the ground up:

  • General lighting and outlets based on the home's square footage
  • Kitchen small-appliance and laundry circuits
  • The nameplate ratings of fixed appliances: range, oven, dryer, water heater, dishwasher, and so on

Then it applies demand factors. The first 8 kVA counts at 100% and the rest at 40%, because no home runs everything at once. Add the new EV charger, and the total is compared against your service.

Good for: Homes with gas heat, a gas range, and a gas dryer, where the electrical load is modest. Harder for: All-electric homes with an electric range, dryer, water heater, and heat pump. On paper they can look "full" even when real use is much lower.

Method 2: The Measured-Demand Method (NEC 220.87)

Instead of estimating, this method uses what your home actually used. The code allows an electrician to:

  1. Take the highest demand your home reached over a 1-year period
  2. Multiply it by 125% as a safety margin
  3. Add the new EV charger load
  4. Confirm the total doesn't exceed the service rating

If a full year of data isn't available, for example after a recent move-in, the code allows a recording meter on the service for at least 30 days, using the highest 15-minute average. The heating or cooling load and other seasonal loads also have to be accounted for.

Good for: Homes that look full on paper but don't actually use that much power at peak.

How SDG&E Usage Data Helps

Most San Diego homes have an SDG&E smart meter, and SDG&E lets you download your own usage through Green Button Download My Data in your My Energy Center account. According to SDG&E, the file includes up to 13 months of smart meter data in hourly or 15-minute intervals.

To get it:

  1. Log in to SDG&E My Energy Center
  2. Open the Usage tab and select your electric meter
  3. Click Green Button Download below the graph
  4. Choose the date range and file format, then download

Sharing that file with your electrician can make the measured-demand method possible, and it shows when your home actually peaks. In many San Diego homes that's summer evenings with the AC running. Never share your SDG&E login. Just send the downloaded file.

Which method is accepted, and what documentation is required, is up to the local building department (City of San Diego, County of San Diego, or your city). Your electrician should confirm before relying on either one. See our guide to EV charger permits in San Diego.

What Happens If the Numbers Don't Fit?

A load calculation that comes up short doesn't automatically mean a new service. Common options include:

Turn the Charger Down

Many Level 2 chargers, including the Tesla Wall Connector, can be set to a lower amperage at install. A smaller circuit uses less capacity and still adds plenty of range overnight for most daily driving.

Use Load Management

Load management (also called energy management or power control) watches your home's total demand and throttles the charger when other big loads are running. Code recognizes these systems for limiting the load a charger adds. This is also how many homes charge two EVs without a panel upgrade.

Free Up Capacity

Sometimes swapping or rebalancing existing loads, or fixing an overcrowded panel, changes the picture. This depends on the specific home.

Upgrade the Panel or Service

When the home simply doesn't have the capacity, or the panel itself is outdated or unsafe, a main panel upgrade is the right fix. It requires SDG&E coordination and a permit, but it also sets the home up for future loads like a heat pump, induction cooking, or a second EV.

What a Load Calculation Doesn't Tell You

A passing calculation is necessary, but it isn't the whole story. A proper EV charger evaluation also looks at:

  • Panel condition: Brand, age, breaker availability, and signs of overheating or damage
  • Wire run: Distance from the panel to where you park, and the route
  • Location: Garage vs outdoor install (see outdoor vs garage EV charger installation)
  • Permit and inspection requirements for your city

Frequently Asked Questions

Can a 100-amp panel handle an EV charger? Sometimes. It depends on what else the home runs, especially electric appliances and AC. A load calculation, and sometimes a lower charger setting or load management, is how you find out. It's never a guess.

Do I need to provide my SDG&E usage data? Not always. The calculated method uses your home's square footage and appliances. Usage data opens up the measured-demand method, which can help homes that look full on paper.

Is the load calculation part of the permit? Building departments often ask for load information with an EV charger permit, especially when the service is small or near capacity. Requirements vary by jurisdiction.

Will a load calculation always say I need a panel upgrade? No. Many homes have room for a Level 2 charger as-is, and others can make it work with a lower amperage setting or load management.

Can LTBL do the load calculation and the install? Yes. We evaluate your panel and service, run the numbers, pull the permit, and install the charger. If a panel upgrade is truly needed, we handle that too.

Get a Straight Answer About Your Panel

LTBL Energy is a licensed California electrical contractor (CSLB #1136922) and a Tesla Certified Installer for the Wall Connector and Powerwall, serving homeowners across San Diego County. We'll tell you honestly whether your panel can handle an EV charger, and what the simplest code-compliant path is if it can't.

Call or text 619-592-6097, or request an EV charger installation quote. A real person replies within 1 hour.

Related Services

Add details (optional)
Are you interested in financing options?

We never collect sensitive financial information here. Financing is offered through Hearth's participating lenders.

Optional photo or document

Add a photo of your panel, roof, or the issue

Tap to browse · PDF, JPG, PNG · 15 MB max

We reply with a real person within 1 hour.

Ready to talk to a licensed local contractor?

LTBL Energy serves San Diego County, CA. Get a straightforward assessment of your solar, battery, panel, or EV charging project.

Call 619-592-6097 Text Free Quote